Slider Pop-Up

This week’s post features a great interactive card, the slider pop-up.  It does what it says on the tin – you slide it and it pops up!  I made this following using a Jennifer McGuire YouTube tutorial for the mechanism and MFT Make A Wish stamps and dies.

First, I cut my card base and layers.  My white layer is the same size as the card front and the checked DSP is ⅜” smaller.  Into the white and checked pieces, I cut a flap, that will be the pop-up element, using my paper trimmer. Another option for this is to use a rectangle die and partial die cutting.  I scored the remaining side of the rectangle and also across the middle of the flap. I cut a hole in the checked piece to make a frame.

After embossing the sentiment, I glued the check DSP onto the white layer before marking the opening of the flap onto the front of the card base. 

This line is to show where to stamp the inside element.  I went for a fun phrase that I had to mask.  The sentiment is quite wide so I stamped in sections, masking out the parts I didn’t want using post-it notes.

The next job was to finish the card front.  I die cut some candles from fancy paper which I glued to white card candles to make them sturdy.  The candles were completed by adding yellow flames and small hearts for the base of the flame.  The centre candles were only glued to the portion of the flap below the fold line to allow them to pop-up.  I also added another sentiment on a flagged banner, only attached to the central candles.

Next was to make the pull tab for the pop up.  This is a piece of card ¾” wider than the window opening and slightly longer than the card, scored at ½” along one of the short edges.  I marked the width of the window opening and trimmed the excess card on the corners of the folded section, then applied adhesive and glued this onto the back of the front flap.

The pull tab is on the left and the folding pop-up section is on the right

Once the slider tab is pulled, some of the tab will be visible so can be decorated.  I stamped some more candles on this, rounded the corners and wrote ‘PULL’ on the top. 

Whilst I was stamping candles, I stamped one on the envelope and onto the card liner.

The final stage is to assemble the card.  Jennifer uses foam tape but I didn’t have any so I applied 3 layers of adhesive tape which seemed enough to create the channel for the tab to slide through.

Here is the finished card…

And when the slide is pulled…

Twist ‘n’ Pop

I’ve been binge watching fancy fold card videos on YouTube lately.  A fancy fold definitely adds a bit of WOW! to a card.  They usually take a little longer to make but are worth the effort.  This card was made using Sam Calcott’s (of Mixed Up Craft fame) tutorial.  Her instructions are really clear and easy to follow.

My theme for this week’s card was a 60th birthday for my friend.  She’s a fun, bubbly and stylish lady so I wanted the same kind of feel for her card.  

To begin, I wanted a black and white striped background.  I only had skinny striped paper so I drew some deliberately wonky lines with my black marker pen and coloured them in, several times, to give a rich black colour.

Next, using my Cricut, I cut my sentiment from black and gold vinyl and stuck it onto the panel.  I added some gold dots in the corners where I would later add the decorative elements.

For the decorative elements, I used Stampin’ Up! Dressed To Impress stamps.  I added a layer of Glossy Accents to the perfume bottle to resemble glass.

Now for the inside.  First, I added some decorative panels to the card base.

Then it was time for the mechanism.  It looks really complicated and would be tricky to explain on paper (screen?!) but Sam explains it really well in her video so I urge you to watch that.  I couldn’t decide what to put on the 4 panels inside until I realised that BIRTHDAY has 8 letters!  There wasn’t room for ‘Happy’ so I added in some small panels to the top of the 1st panel and bottom of the 4th panel for the ‘Happy’ and ‘Katie’ to personalise the card.  I trialled about 4 small panels until I got ones that were the right size and didn’t drag on card as it opened and closed.

The final job was to glue the front panel into the card base and add some gold-coloured gems for extra pizzazz.

This was such a fun card to make and I think it definitely has the WOW! factor I was after. Here’s a short clip of my card in action.

Swing Fold Card

This fancy fold card style has lots of dimension and extra wow! when it’s opened and the parts move.  It may look a little complicated but it’s not really.

To begin, I cut my card base and a layer of DSP and cut a rectangle from the front of the pair of them, attached together with a little temporary adhesive.  The piece of card base will be used later so don’t discard it!

Next, I cut the liner, which is also the mechanism to make the swing fold.  Score the card at ¼, ½ and ¾ across the piece and fold ‘mountain-mountain-valley’, as shown in the photo.

Place the liner with the first ‘mountain’ fold facing up into the card front and mark the left-hand side of the hole.  Remove the liner and cut away slightly bigger than the hole using either a trimmer or I used the next size up rectangle die and the partial die-cutting technique.

The liner is then glued into the card base by adhering the bit around the cut away to the back of the opening and the last quarter of the lining to the right-hand side of the back of the card base. 

After gluing the DSP onto the front, I attached the swing panel, which is the section of card base cut out at step 1.  Apply the glue to the swing mechanism only and attach the panel.

Lastly, decorate as you wish!

I used Stampin’ Up! Pampered Pets for my cards.

It’s also possible to make this card in landscape format too and using an oval cut out rather than a rectangle.

I think I’ll try a square version next time to give more space for writing my message.

Images © 2021 Stampin’ Up!